Don't click on this logo on this page  

ROMPPAI'S Outdoors, your out door specialist  

      If your order is small, you can put you order in the note box, on our credit card summation page, Note any orders under $50.00 CND a $5.00 handling charge will be added.

Download our order form, if you have excel Click here if you do not have excel down load it in PDF Click Here - MESSAGE BOARD

  Our Credit card, and order summation pages are  a 256-bit SSL secure connection, to check our security certificate click the image below "ONLY on those pages

 Outboards Scoters/Mopeds  Furnaces  E-Bike  Custom Pontoons Romppai's name brand Fishing Tackle

 

Check it out before you buy

Furnaces, Furnaces and more Furnaces

HOME COMFORT PRODUCTS

The Shinook: Ceiling Mounted Heater

"It's too hot over here... it's too cold over there..."

Achieving a uniformly comfortable environment in workshopsShinook, warehouses and other rooms with high ceilings has always been a problem. With the Shinook hydronic ceiling mounted heater you can now have uniform heat distribution in buildings with high ceilings - 12' or more!

The Shinook Hydronic Heater provides uniform heat distribution in rooms with high ceilings.

How it works:

The Shinook consists of a spiral thread, aluminum, rib-tube element through which hot water is circulated. A fan, with specially designed blades, is mounted above the rib-tube element. The fan blades are designed to gently push a continuous stream of warmed air down and out to the bottom perimeter of the room (A).

The pressure of the fan then causeShinook-Flows the air to circulate in both directions from the bottom perimeter (B). Cooled air is continuously drawn back to the Shinook for reheating and distribution while warm air is continuously pushed to the bottom perimeter of the room. As a result you get very uniform horizontal heat distribution in the bottom of the room. Fan blades are adjustable to match your room size.

In traditional air heating systems a small quantity of air is strongly heated. The hot air rises to the ceiling thus creating a large and extremely uneconomical vertical temperature difference.

The Shinook continuously circulates a large quantity of air and only increases its temperature slightly. The result is uniformly heated air throughout the entire room. You get a more comfortable heating system and lower heating costs.

Specifications

Air Capacity Approx 575,000 cu.ft./hr
Air Stream Adjustable & Controllable
Motor 1/2 hp 120V; 860 rpm
(Controllable)
Heat Capacity 18.5 KW 56,000 BTU
water temp. 90°/70°C
Water Resistance 1.24 p.s.i
Connection Size
@ Water Side		 3/4" outside thread
Weight 57 lbs.

    Advantages

  • Energy savings of up to 30% may be realized
  • Ceiling mounted the Shinook does not interfere with equipment placement in the room
  • Low speed, high output fan is very quiet
  • Better horizontal air distribution increases comfort levels. No hot spots or cold draughts
  • Easily installed, long life and virtually maintenance free

 

We have forced air Furnaces

Natural Gas and Propane Boilers (SEE OUR CATALOG)

We have oil boilers, oil wood boilers

We have electric boilers, electric, an wood (SEE OUR CATALOG)

 
 
 
 
 
 
 
 
 
 
 
 
 

Download a complete catalog, of parts, for heating, or pluming, boiler Pex and Pex-all Pex pipe, insolated under ground Pex, and fittings, copper manifolds, stainless steel manifolds with controllers, copper, stainless steel and brass fittings, Valves, mixing valves, circulating pumps for boilers and domestic hot water, zone valves, controllers and so much more. Every thing you need for the do it you self, (DIY), or we can do the whole job for you.  pricing is now in the catalog, however shipping charges are over and above on large items, such as furnaces, and wall raids, possibly. Any product orders shipped out from our location, will have shipping and tax add, unless it is a very large order.

We sell only top quality products, we learned our lesson years ago, you get what you pay for, take it from me, when I build our place, I went to a big pluming supplier, and bought all the copper fittings, valves and pipe, when I brought all the stuff home, my wife at the time, said, wow, you paid all that for this, she told me she seen it cheaper in a big box store, she took all the stuff back to the pluming warehouse, and went to that box store, and bought all the stuff for a little more then half the price. Well for the next 4 years I spent ripping this place apart every time a fitting or valve sprung a leak, yes every fitting and valve sprayed water out of the main housing, like a small pin hole, not to mention the big mess every time, and the damage it did.

Well after 4 years, I replace every fitting and valve in the place.. now did we save money in the long run? No it cost us three to four times the price for the parts and repairs in the end, and that's not counting all the extra materials an labor I had to do over the 4 years.